Mesoporous Ag@WO3 core-shell, an investigation at different concentrated environment employing laser ablation in liquid.

In this study, silver-tungsten oxide core-shell nanoparticles (Ag-WO3 NPs) were synthesized by pulsed laser ablation in liquid employing a (1.06 µm) Q-switched Nd:YAG laser, at different Ag colloidal concentration environment (different core concentration). The produced Ag-WO3 core-shell NPs were subjected to characterization using UV-visible spectrophotometry, X-ray diffraction (XRD), transmission electron microscopy (TEM), energy-dispersive spectroscopy, electrical analysis, and photoluminescence PL. The UV-visible spectra exhibited distinct absorption peaks at around 200 and 405 nm, which attributed to the occurrence of surface Plasmon resonance of Ag NPs and WO3 NPs, respectively. The absorbance values of the Ag-WO3 core-shell NPs increased as the core concentrations rose, while the band gap decreased by 2.73-2.5 eV, The (PL) results exhibited prominent peaks with a central wavelength of 456, 458, 458, 464, and 466 nm. Additionally, the PL intensity of the Ag-WO3-NP samples increased proportionally with the concentration of the core. Furthermore, the redshift seen at the peak of the PL emission band may be attributed to the quantum confinement effect. EDX analysis can verify the creation process of the Ag-WO3 core-shell nanostructure. XRD analysis confirms the presence of Ag and WO3 (NPs). The TEM images provided a good visualization of the core-spherical shell structure of the Ag-WO3 core-shell NPs. The average size of the particles ranged from 30.5 to 89 (nm). The electrical characteristics showed an increase in electrical conductivity from (5.89 × 10-4) (Ω cm)-1 to (9.91 × 10-4) (Ω cm)-1, with a drop in average activation energy values of (0.155 eV) and (0.084 eV) at a concentration of 1.6 µg/mL of silver.

Effect of laser fluence on the optoelectronic properties of nanostructured GaN/porous silicon prepared by pulsed laser deposition.

In this study, the fabrication of nanostructured GaN/porous Si by pulsed laser deposition (PLD) was demonstrated. The porous silicon was prepared using laser-assisted electrochemical etching (LAECE). The structural, optical, and electrical properties of GaN films were investigated as a function of laser fluence. XRD studies revealed that the GaN films deposited on porous silicon were nanocrystalline, exhibiting a hexagonal wurtzite structure along the (100) plane. Spectroscopic property results revealed that the photoluminescence PL emission peaks of the gallium nitride over porous silicon (GaN/PSi) sample prepared at 795 mJ/mm2 were centered at 260 nm and 624 nm. According to topographical and morphological analyses, the deposited film consisted of spherical grains with an average diameter of 178.8 nm and a surface roughness of 50.61 nm. The surface of the prepared films exhibited a cauliflower-like morphology. The main figures of merit of the nanostructured GaN/P-Si photodetectors were studied in the spectral range of 350-850 nm. The responsivity, detectivity, and external quantum efficiency of the photodetector at 575 nm under - 3 V were 19.86 A/W, 8.9 × 1012 Jones, and 50.89%, respectively. Furthermore, the photodetector prepared at a laser fluence of 795 mJ/mm2 demonstrates a switching characteristic, where the rise time and fall time are measured to be 363 and 711 µs, respectively.

Preparation of GaN/Porous silicon heterojunction photodetector by laser deposition technique.

In this work, gallium nitride (GaN) thin film was deposited on porous silicon (PSi) substrate via a pulsed laser deposition route with a 355 nm laser wavelength, 900 mJ of laser energy, and various substrate temperatures raging from 200 to 400 °C. The structural and optical properties of GaN films as a function of substrate temperature are investigate. XRD studies reveal that the GaN films deposited on porous silicon are nanocrystalline with a hexagonal wurtzite structure along (002) plane. The photoluminescence emission peaks of the GaN/PSi prepared at 300 °C substrate temperature are located at 368 nm and 728 nm corresponding to energy gap of 3.36 eV and 1.7 eV, respectively. The GaN/PSi heterojunction photodetector prepared at 300 °C exhibits the maximum performance, with a responsivity of 29.03 AW-1, detectivity of 8.6 × 1012 Jones, and an external quantum efficiency of 97.2% at 370 nm. Similarly, at 575 nm, the responsivity is 19.86 AW-1, detectivity is 8.9 × 1012 Jones, and the external quantum efficiency is 50.89%. Furthermore, the photodetector prepared at a temperature of 300 °C demonstrates a switching characteristic where the rise time and fall time are measured to be 363 and 711 µs, respectively.

Silver decorated lithium niobat nanostructure by UV activation method for silver-lithium niobate/silicon heterojunction device.

Lithium niobite (LiNbO3) nanostructure were successfully synthesized by chemical bath deposition method (CBD) and then decorated with silver nitrate (AgNO3) through UV activation method at different immersion durations (5, 15, 25, 35, and 45 s). The silver nanoparticles (AgNPs) effects on the optical and structural properties were studied and analyzed using various scientific devices and technique. X-ray diffraction (XRD) results showed that all the samples have a hexagonal structure with a maximum diffraction peak at the (012), and the existence of silver atoms could be recognized at 2θ = 38.2° which corresponds to the (111) diffraction plane. The optical absorption of nanocomposites depicted the presence of plasma peak related to silver (Ag) at 350 nm. The estimated energy gap from the optical absorption revealed a reduction in the Eg value from (3.97 eV) to (3.59 eV) with the presence of Ag atom. The Photolumincence (PL) peaks were observed at around 355 nm for pure LiNbO3/Si and 358, 360, 363, 371, 476 nm for different immersion durations respectively, in the visible region of the electromagnetic spectrum. The scanning electron microscopy (SEM) study illustrated that with increasing the immersion time, especially at 45 s, a change in the particle morphology was observed (LiNbO3 NRs structure). Atomic force microscopy (AFM) displayed that the surface roughness decreases from 80.71 nm for pure sample to 23.02 nm for the decorated sample as the immersion time is increased. FT-IR manifested a noticeable increase in the intensity of the peaks of samples decorated with AgNPs. Raman spectroscopy elucidated that the peaks shifted to higher intensity due to the plasmonic effect of Ag nanoparticles. Ag-LiNbO3/Si heterojunction nano-devices were fabricated successfully and enhanced the optoelectronic properties in comparison with the pure LiNbO3/Si heterojunction device.

A gold nanoparticles coated unclad single mode fiber-optic sensor based on localized surface plasmon resonance.

In the last few decays, the fiber-optic was employed in the field of sensing because of its benefits in contrast to other types of sensors such as small size, easy to fabricate, high response, and flexibility. In this study, unclad single mode fiber-optic sensor is proposed to operate at 650 nm wavelength. COMSOL Multiphysics 5.1 finite element method (FEM) is used to design the sensor and tested it theoretically. The middle portion of the fiber cladding is removed and replaced by gold nanoparticles (Au NPs) of 50 nm thickness. Analytic layer of 3 µm thickness was immersed in different liquids in range of refractive index (RI) from 1.000281 to 1.39. These liquids are NaCl Deionized (DI) water solution, sucrose-Deionized (DI) water solution, and glycerol solution Deionized (DI) water. It was found that the highest obtained sensitivity and resolution are for glycerol-DI water solution with value of 3157.98 (nm/RIU) and 3.16 × 10-5 (RIU), respectively. Furthermore, it is easy to fabricate and of low cost. In experiments, pulsed laser ablation (PLA) was used to prepare Au NPs. X-ray diffraction (XRD) shown that the peak of the intensity grew as the ablated energy increased as well as the structure crystallization. Transmission electron microscopy (TEM) revealed an average diameter of 30 nm at the three ablated energies, while X-ray spectroscopy (EDX) spectrum has indicated the presence of Au NPs in the prepared solution. The photoluminescence (PL) and ultraviolet-visible UV-Vis transmission were used to study the optical properties of the prepared Au NPs. An optical spectrum analyzer was used to obtain the sensor's output results. It has shown that best intensity was obtained for sucrose which confined with theoretical results.

Design of an unclad single-mode fiber-optic biosensor based on localized surface plasmon resonance by using COMSOL Multiphysics 5.1 finite element method.

This study proposed an unclad optical fiber biosensor based on the localized surface plasmon resonance phenomenon and operating at 650 nm using COMSOL Multiphysics 5.1 finite element method (FEM). Gold nanoparticles (50 nm thickness) were coated on the middle portion of the unclad fiber. Air, water, blood plasma, liver tissue, colon tissue, and pentanol (C5H11OH) were used as analytical layers with 3 µm. The sensor serves as a theoretical foundation for experimental research. The blood plasma had the highest sensitivity with a sensitivity of 10,638.297 nm/RIU and a resolution of 9.410-6RIU. The proposed sensor is a promising candidate for a low-cost, simple-geometry biochemical sensing solution.

Effect of multipath laser shock processing on microhardness, surface roughness, and wear resistance of 2024-T3 Al alloy.

Laser shock processing (LSP) is an innovative surface treatment technique with high peak power, short pulse, and cold hardening for strengthening metal materials. LSP is based on the application of a high intensity pulsed laser beam (I > 1 GW/cm(2); t < 50 ns) at the interface between the metallic target and the surrounding medium (a transparent confining material, normally water) forcing a sudden vaporization of the metallic surface into a high temperature and density plasma that immediately develops inducing a shock wave propagating into the material. The shock wave induces plastic deformation and a residual stress distribution in the target material. In this paper we study the increase of microhardness and surface roughness with the increase of laser pulse energy in 2024-T3 Al alloy. The influence of the thickness of the confining layer (water) on microhardness and surface roughness is also studied. In addition, the effect of LSP treatment with best conditions on wear behaviors of the alloy was investigated.

Characterization of nanostructured hydroxyapatite prepared by Nd:YAG laser deposition.

Pulsed laser deposition, under dry and water vapor conditions, was employed to synthesize nanostructured hydroxyapatite films by pulsed laser deposition (PLD) of chlorapatite target for the purpose of coating metallic bone implants by this material. A pulsed Nd:YAG laser operating at a wavelength of 1064 nm and emitting 9 ns pulses was used for deposition. AFM microscopy, FTIR spectroscopy, optical microscopy, adhesion and microhardness measurements were conducted to characterize the films. The in vitro test for the synthesized hydroxyapatite was performed using simulated body fluid (SBF). The results showed a successful transformation of the chlorapatite to hydroxyapatite films characterized by all the HAp peaks with 60 nm root mean square roughness, (80-327)nm grain size, and a microhardness of 512 HV.